Penetrating Oil Showdown Episode 2. Will Seafoam Deep Creep prevail?

This test demonstrates that not all penetrating oils are equal. In fact, the see-through plastic/rusty bolt test shows which ones actually penetrate and which ones don't. Which penetrating fluid is best? In this showdown, Brake Fluid, Seafoam Deep Creep, Fluid Film, BG In-Force, WD-40 Rust Specialist, CRC Knock'er Loose. Consider selecting the bell in the upper right hand corner to get notified of future videos. Deep Creep won the competition with CRC Knock-er Loose coming in a close 2nd. Thank you very much for supporting the channel through Patreon and watching the commercials.
Could break fluid possibly work better. than penetrating fluid when it comes to . loosening rusty bolts today we're gonna . find out once and for all whether or not . this is gonna work the best because i've . had a lot of people asked me to test . against these other brands of . penetrating fluids now in a previous . video we tested acetone atf mix against . a lot of different penetrating fluids . what we found was quite interesting and . that is that acetone atf actually came . in second place just behind liquid winch . which took the top spot so let's get the . testing underway and find out once and . for all just how good brake fluid does . when it comes to removing rusty bolts . just like in the previous video i'll be . using a half inch wheel lug studs and . nuts. i've only torqued in 280 foot-pounds . this time though because my torque. adaptor only goes up two hundred . forty-seven foot-pounds i do have a . larger torque adapter if we need it but. i don't like to change test devices in . the middle of a test i really like it . when you guys provide comments and . constructive feedback it helps me . improve the science so based on the . recommendations you guys provided i'll . be applying each penetrating fluid with . a dripper instead of using the spray can . also value the washer so please keep the . recommendations coming because it does . help me do penetrating fluids actually . work i drilled in tap a one-inch piece . of plexiglass and then i oxide eyes the . bolts additionally i added a hot blue. perimeter at the top obviously. metal-on-metal causes twice the rust as . metal on plastic however this will . provide some evidence as to whether or . not penetrating fluids do any good so . i've got a total of twenty eight bolts . work with the first four include our . control group so i'm gonna go ahead and . loosen those and see how much torque it . takes. [music]. dependent training fluids actually creep . in the rusted parts the nut was threaded . onto the ball three-quarters of the way . by hand then the nut and bolt were . oxidized so what we'll do is apply the . penetrating fluid that wins a. competition to the top of this nut so we . can see if it can creep all the way . through the rust and out the bottom so . first up we'll be testing do t3 brake . fluid . [music]. so crc knocker loose loosens frozen . metal parts dissolves rust and corrosion . lubricates and prevents rust . seafoam deep creep powers through . breasts and varnish . [music]. so fluid found penetrates to free up . heavily seized parts . [music]. so bg in force has an ion activated . formula that permeates metal better than. standard formula penetrating oils in a. previous video we tested wd-40 this time . we're testing the specialist which is . specifically designed as a rust release . penetrant spray so the brake fluid seems. to have remained on the the washer did . not spread beyond the washer it also did . not evaporate okay this is crc knocker . loose what's interesting is the. penetrating fluid seems like it's mostly . dried up there's a little bit towards . the base of the nut as well as it looks . like it started to move away from the . washer just a little bit okay so seafoam . deep creep seems like it is very similar . to the the crc knocker loose however it . doesn't seem to have spread away from . the washer as much it still seems like. there's a little bit more content . remaining on the threads as well as the . nut okay this is fluid film it's very . clear it's much different the rest of . them it looks like it's slimed in this . entire set of nuts and bolts . so bg in force looks like it's float all . the way down the nut and on down into . the washer it's also hasn't evaporated . as quickly as some of the other products . okay one of the comments that people . made last time is that it's not . realistic to apply a penetrating fluid . three times over three hours what they . wanted me to test was applying a . penetrating fluid giving it some time to . work and then try to loosen the bolts so . what we're going to do is come back in . an hour. and we run a test on each one of these . to see how much torque it takes for . these to come loose well we're allowing . the penetrating fluids to go to work on . the rusty nuts and bolts we're going to . go ahead and apply these products to . this setup . [music]. [music]. as you can see brake fluid actually . penetrated and went all the way down to . the bottom of the bulb . crc knocker loose did a great job as . well a thoroughly penetrated went all . the way down to the bottom of the bolt . sea foam did a great job there's a lot . of sea foam that has thoroughly . penetrate it's actually sitting in a . puddle of sea foam you can see it about . to drip off this stuff really seems to . work well . this is fluid film it does not appear to . have done much as far as penetrating . most of the fluid film seems to remain. up top. [music]. as you can see bg and force did not . fully penetrate and they can all the way. to the bottom of the bolt there's a lot . of penetrating fluid still at the top of . the threads that has not worked its way . to the bottom so does look like bg . enforce did go down to thread some but . not quite as well as some of the other . products we've tested deputy brush . specialists did a really good job it has . gone all the way down to the bottom of . the bowl okay it's been an hour . schooling to begin testing . [music]. [music]. [music]. [music]. [music]. what do i do now is remove each one of . these nuts to see how much penetration . occurred. [music]. [music]. good guys slight change of plans i was . gonna put the top penetrating fluid on . this bolt and this nut to see if they . could thoroughly penetrate after did. last video i had a lot of requests to . just mix them all together and see if it . would work well so i decided to do is . just take a little bit of each dump it . into one stir it up and then drop it on . top of this to see if it made a . difference now i never recommend mixing . chemicals because we could experience a . chemical reaction if that's the case i'm . gonna have to open up the shop door and . get the fans running . [music]. so it doesn't appear that the fluid has . penetrated anything i don't think mixing . them all together is such a great idea . after all . in fact it's this it's stuck on there . this isn't moving and there's no fluid . that's gone past the bottom of the nut . what i'm gonna do is soak up the . penetrating fluid and then remove the . nut and see how far down it made it it's . all wet right now but i think that's . because the fluid that was in there as i . was turning the ball it started to flow . downward but it took fifty six point . four foot-pounds of torque to break this . loose and again this wasn't torque it . was a put-on by hand so based upon the . plexiglass test as well as how far the . penetrating fluids traveled down to . threads the result seemed to make sense . with seafoam deep creek coming out on . top followed by crc knocker loose coming . in second now regarding the other . products and compared to the last test . there just wasn't a lot of time for . these products to do their job as you . remembered last video it was a . three-hour test for three applications . but viewers said it did not make sense . to do a three-hour test because in the . real world no one waits three hours for . penetrating fluid to do its job which is . why tested differently this time please . let me know if you'd like to see a . showdown between seafoam and liquid . wrench if i can put together a video on . that or if you like me to test other . penetrating fluids thanks so much for . watching the video and i look forward to . seeing you next time . .
Tags:  additive  aerokroil  crankcase  crc  heat  kroil  loctite  lucas  marvel  marvels  oil  rust  rusty  seafoam  seefoam  torch  wd-40  penetrating  oil  showdown  episode  2.  will  seafoam  deep  creep  prevail? 

Number of Views: 2,539,307
Number of Likes: 33,093
Category: Style

You may also like: